.KEM-PK10884 Model T6500, T6530, T6550.Safety and General Information. 2 FCC Licensing Information.10 Control Buttons.11 Getting Started.12 Installing the the AA Batteries.12 Installing the NiMH Battery Pack.12 Battery Meter.13 Attaching the Belt Clip.Safety and General Information Safety and General Information 2 Important Information on Safe and Efficient Operation Read This Information Before Using Your Radio.

• Motorola Talkabout T5500 User Manual
• Motorola Talkabout 5500 Manual Download

The information provided in this document supersedes the general safety information in user guides published prior to December 1, 2002. Transmit and Receive Procedure Your two-way radio contains a transmitter and a receiver.To assure optimal radio performance and make sure human exposure to radio frequency electromagnetic energy is within the guidelines set forth in the above standards, always adhere to the following procedures.

Portable Radio Operation and EME Exposure Antenna Care Use only the supplied or an approved replacement antenna. Unauthorized antennas, modifications, or attachments could damage the radio and may violate FCC regulations. DO NOT hold the antenna when the radio is “IN USE.Safety and General Information Two-way Radio Operation 4 When using your radio as a traditional two-way radio, hold the radio in a vertical position with the microphone 1 to 2 inches (2.5 to 5 cm) away from the lips.

Body-Worn Operation To maintain compliance with FCC/Health Canada RF exposure guidelines, if you wear a radio on your body when transmitting, always place the radio in a Motorola-supplied or approved clip, holder, holster, case, or body harness for this product.1. This device may not cause harmful interference; and 2. This device must accept any interference received, including interference that may cause undesired operation. Facilities To avoid electromagnetic interference and/or compatibility conflicts, turn off your radio in any facility where posted notices instruct you to do so. Hospitals or health care facilities may be using equipment that is sensitive to external RF energy. Aircraft When instructed to do so, turn off your radio when on board an aircraft.Safety and General Information Medical Devices - Hearing Aids 6 Some digital wireless radios may interfere with some hearing aids.

In the event of such interference, you may want to consult your hearing aid manufacturer to discuss alternatives. Other Medical Devices If you use any other personal medical device, consult the manufacturer of your device to determine if it is adequately shielded from RF energy. Your physician may be able to assist you in obtaining this information.Turn off your radio prior to entering any area with a potentially explosive atmosphere, unless it is a radio type especially qualified for use in such areas as “Intrinsically Safe.” Do not remove, install, or charge batteries in such areas. Sparks in a potentially explosive atmosphere can cause an explosion or fire resulting in bodily injury or even death.Safety and General Information Batteries 8 All batteries can cause property damage and/or bodily injury such as burns if a conductive material such as jewelry, keys, or beaded chains touch exposed terminals. The conductive material may complete an electrical circuit (short circuit) and become quite hot. Exercise care in handling any charged battery, particularly when placing it inside a pocket, purse, or other container with metal objects. Battery Charger Safety Instructions Save these Instructions 1.Safety and General Information 7.

Make sure the cord is located so it will not be stepped on, tripped over, or subjected to damage or stress. An extension cord should not be used unless absolutely necessary. Use of an improper extension cord could result in a risk of fire and/or electric shock. If an extension cord must be used, make sure that:. The pins on the plug of the extension cord are the same number, size and shape as those on the plug of the charger.FCC Licensing Information FCC Licensing Information 10 Your Motorola radio operates on General Mobile Radio Service (GMRS) frequencies and is subject to the Rules and Regulations of the Federal Communications Commission (FCC). The FCC requires that all operators using GMRS frequencies obtain a radio license before operating their equipment.

IntroductionCongratulations on your purchase of a Motorola product!Product registration is an important step. Registering helps us facilitate warranty service and permits us to contact you should your Motorola product require an update or other service.To register your product on-line, visit www.motorola.com/warranty/radios.Please retain your original dated sales receipt for your records. For warranty service of your Motorola product, you will need to provide a copy of your dated sales receipt to confirm warranty status. Registration is not required for warranty coverage.For a copy of a large-print version of this guide, or for product-related questions, call:1-800-353-2729 in the USA1-888-390-6456 TTY (Text Telephone)On the web, please refer to www.motorola.com/talkabout.

1Safety and General Information. 3FCC Licensing Information.

11Control Buttons - Models T5600,T5700. 12Control Buttons - Models T5620,T5710, T5720. 13Getting Started. 14Installing the AA Batteries.14Installing the NiCd Battery Pack.14Battery Meter.15Using the Desk Stand Charger(Optional Accessory).15Attaching the Belt Clip.17Removing the Belt Clip.17Turning Your Radio On and Off.17Setting the Volume.17Setting a Channel.18Channels and Frequencies.19Talking and Listening.

20Talk Range.20Checking the Channel BeforeTransmitting.20. Special Features.21Interference Eliminator Code. 21 Push to Talk Timeout Timer. 21 Locking the Keypad. 22 Scanning Channels (Models T5620,T5700, T5710 Only).

22 Scan Advance. 23 Removing Channels from the Scan List(Nuisance Delete Feature). 23Alerts.24Channel Busy Indicator. 24 Setting and Transmitting Call Tones. 24 Transmitting a Talk Confirmation Tone 25 QT Noise Filtering (Models T5700,T5710, T5720 Only).

25Accessories.27Using Audio Accessories. 27 Voice Activation (VOX) Accessories(Models T5710, T5720 Only). 27 Setting the Sensitivity Level(Models T5710, T5720 Only).

28Patent Information.29 Export Law Assurances.29. Safety and General InformationImportant Information on Safe and Efficient Operation Read This Information Before Using Your RadioThe information provided in this document supersedes the general safety information contained in user guides published prior to July 2000.Transmit and Receive ProcedureYour two-way radio contains a transmitter and a receiver. American National Standards Institute (ANSI)/Institute of Electrical and Electronic Engineers (IEEE) C95.

1-1992. Institute of Electrical and Electronic Engineers (IEEE) C95.1-1999 Edition. International Commission on Non-Ionizing Radiation Protection (ICNIRP) 1998. Ministry of Health (Canada) Safety Code 6.

Two-Way Radio OperationWhen using your radio as a traditional two-way radio, hold the radio in a vertical position with the microphone one to two inches (2.5 to 5 cm) away from the lips.Body-Worn OperationTo maintain compliance with FCC/Health Canada RF exposure guidelines, if you wear a radio on your body when transmitting, always place the radio in a Motorola-supplied or approved clip, holder, holster, case, or body harness for this product. Use of non- Motorola-approved accessories may exceed FCC/Health Canada RF exposure guidelines. FacilitiesTo avoid electromagnetic interference and/or compatibility conflicts, turn off your radio in any facility where posted notices instruct you to do so.

Hospitals or health care facilities may be using equipment that is sensitive to external RF energy.AircraftWhen instructed to do so, turn off your radio when on board an aircraft. Any use of a radio must be in accordance with applicable regulations per airline crew instructions.Medical Devices - PacemakersThe Advanced Medical Technology Association recommends that a minimum separation of six inches (15 cm) be maintained between a handheld wireless radio and a pacemaker. These recommendations are consistent with the independent research by, and recommendations of the U.S. Food and Drug Administration.Persons with pacemakers should:. ALWAYS keep the radio more than six inches (15 cm) from their pacemaker when the radio is turned ON. Not carry the radio in the breast pocket. Use the ear opposite the pacemaker to minimize the potential for interference.

Turn the radio OFF immediately if you have any reason to suspect that interference is taking place. Medical Devices - Hearing AidsSome digital wireless radios may interfere with some hearing aids. In the event of such interference, you may want to consult your hearing aid manufacturer to discuss alternatives.Other Medical DevicesIf you use any other personal medical device, consult the manufacturer of your device to determine if it is adequately shielded from RF energy. Your physician may be able to assist you in obtaining this information.Safety and General Use While DrivingCheck the laws and regulations on the use of radios in the area where you drive. Always obey them.

When using your radio while driving, please:. Give full attention to driving and to the road. Use hands-free operation, if available. Pull off the road and park before making or answering a call if driving conditions so require.Operational WarningsFor Vehicles with an Air BagDo not place a portable radio in the area over an air bag or in the air bag deployment area.

Air bags inflate with great force. If a portable radio is placed in the air bag deployment area and the air bag inflates, the radio may be propelled with great force and cause serious injury to occupants of the vehicle. Potentially Explosive AtmospheresTurn off your radio prior to entering any area with a potentially explosive atmosphere, unless it is a radio type especially qualified for use in such areas as “Intrinsically Safe.” Do not remove, install, or charge batteries in such areas. Sparks in a potentially explosive atmosphere can cause an explosion or fire resulting in bodily injury or even death.Note: The areas with potentially explosive atmospheres referred to above include fueling areas such as below decks on boats, fuel or chemical transfer or storage facilities, areas where the air contains chemicals or particles, such as grain, dust or metal powders, and any other area where you would normally be advised to turn off your vehicle engine. Areas with potentially explosive atmospheres are often but not always posted.Blasting Caps and AreasTo avoid possible interference with blasting operations, turn off your radio when you are near electrical blasting caps, in a blasting area, or in areas posted: “Turn off twoway radio.” Obey all signs and instructions.Operational CautionsAntennasDo not use any portable radio that has a damaged antenna.

If a damaged antenna comes into contact with your skin, a minor burn can result. BatteriesAll batteries can cause property damage and/or bodily injury such as burns if a conductive material such as jewelry, keys, or beaded chains touch exposed terminals. The conductive material may complete an electrical circuit (short circuit) and become quite hot. Exercise care in handling any charged battery, particularly when placing it inside a pocket, purse, or other container with metal objects.Battery Charger Safety Instructions Save these Instructions1. Do not expose the charger to rain or snow.2. Do not operate or disassemble the charger if it has received a sharp blow, or has been dropped or damaged in any way.3.

Never alter the AC cord or plug provided with the unit. If the plug will not fit the outlet, have the proper outlet installed by a qualified electrician. An improper condition can result in a risk of electric shock.4. To reduce the risk of damage to the cord or plug, pull the plug rather than the cord when disconnecting the charger from the AC receptacle.5. To reduce the risk of electric shock, unplug the charger from the outlet before attempting any maintenance or cleaning.6.

Use of an attachment not recommended or sold by Motorola may result in a risk of fire, electric shock, or personal injury.7. Make sure the cord is located so it will not be stepped on, tripped over, or subjected to damage or stress. An extension cord should not be used unless absolutely necessary.

Use of animproper extension cord could result in a risk of fire and/or electric shock. If anextension cord must be used, make sure that:Information.

The pins on the plug of the extension cord are the same number, size, andshape as those on the plug of the charger. The extension cord is properly wired and in good electrical condition.

The cord size is 18 AWG for lengths up to 100 feet, and 16 AWG for lengths upto 150 feet.GeneralandSafety9. The supply cord of this charger cannot be replaced.

If the cord is damaged, callMotorola Product Services at 1-800-353-2729 in the USA or 1-888-390-6456TTY (Text Telephone). FCC Licensing InformationYour Motorola radio operates on General Mobile Radio Service (GMRS) frequencies and is subject to the Rules and Regulations of the Federal Communications Commission (FCC).

The FCC requires that all operators using GMRS frequencies obtain a radio license before operating their equipment. To obtain the FCC forms, please request Forms 605 and 159, which includes all forms and instructions.

If you wish to have the document faxed or mailed, or have questions, please use the following contact information.FaxedMailedQuestionsContact the Fax-On-Call the FCC formsRegarding FCC licenseDemand system at:hotline at:Contact the FCC at:1-800-418-FORM1-888-CALL-FCC1-202-418-01771-888-225-53221-800-418-3676Or: or modifications not expressly approved by Motorola may void the user’s authority granted by the FCC to operate this radio and should not be made. To comply with FCC requirements, transmitter adjustments should be made only by or under the supervision of a person certified as technically qualified to perform transmitter maintenance and repairs in the private land mobile and fixed services as certified by an organization representative of the user of those services.

Replacement of any transmitter component (crystal, semiconductor, etc.) not authorized by the FCC equipment authorization for this radio could violate FCC rules.Note: Use of this radio outside the country where it was intended to be distributed is subject to government regulations and may be prohibited. Getting StartedInstalling the AA BatteriesYour radio uses 3 AA Alkaline batteries.1.

With the back of the radio facing you, lift the battery latch up to release the battery cover and remove the cover.2. Insert 3 AA Alkaline batteries as shown on the inside of the battery compartment.3.

Reposition the battery cover and press down to secure.Note: The T5600, T5620, T5700, T5710, and T5720 model radios can use a NiCd rechargeable battery insteadof 3 AA Alkaline batteries. A rechargeable battery upgrade kit, model number 53614, is available for these radios. For the dealer nearest you, call 1-800-353-2729 in the USA, or visit our website at www.motorola.com/talkabout.Installing the NiCd Battery Pack1. Follow step 1 above to remove the battery cover.2. Remove the battery pack from the clear plastic bag.Do not disassemble or unwrap the battery pack.3. Insert the NiCd battery pack so the metal contacts on the side of the battery are facing outward from the radio to connect with the contacts on the battery door.4.

Reposition the battery cover and press down to secure. Battery MeterThe battery icon shows the battery charge level, from full d to empty a.When the battery is empty, the radio chirps periodically after releasing M.The radio powers off when the voltage drops below a predetermined level to protect the rechargeable battery.Note: Remove the batteries before storing your radio for extended periods of time.

Batteries corrode over time and may cause permanent damage to your radio.Using the Desk Stand Charger (Optional Accessory)The desk stand charger provides drop-in charging convenience for NiCd batteries and can be placed on any flat surface, such as a desk or workbench. Charge the NiCd battery overnight (at least 16 hours) before using it for the first time. After the initial charge, an empty battery is fully charged within 14 hours.1. Turn the radio off and remove the battery cover.2. Remove the battery pack from the clear plastic bag.Do not disassemble or unwrap the battery pack.3. Insert the NiCd battery pack so the metal contacts on the side of the battery are facing outward from the radio to connect with the contacts on the battery door. 5.Plug the AC power supply into the plug on the desk stand.6.Plug the AC power supply into a standard wall outlet.7.Slide the radio into one of the charging pockets facing forward.To charge the battery pack separately from the radio:Started1.Remove the battery pack from the clear plastic bag.Do not disassemble or unwrap the battery pack.2.Insert the battery pack into the charging pocket.

Make sure the metal contactsGettingon the side of the battery are making contact with the contacts inside thecharger.3.Plug the AC power supply into the plug on the desk stand.4.Plug the AC power supply into a standard wall outlet.Notes. When moving between hot and cold temperatures, do not charge the battery until the battery temperature acclimates (usually about 20 minutes). For optimal battery life, remove the radio or battery from the charger within. Attaching the Belt Clip1.

Align the belt clip post with the hole in the back of the radio.2. Gently push until the clip clicks into place.Removing the Belt Clip1. Push down on the release tab at the top of the belt clip to release the catch.2.

Pull the belt clip away from the back of the radio.Turning Your Radio On and OffTurn P clockwise to turn the radio on and counterclockwise to turn the radio off.The radio chirps and the display briefly shows all feature icons available on your radio. The display then scrolls through the available channels and Interference Eliminator Codes. Setting the VolumeRotate P while holding down Q or J until you reach a comfortable listening level. Rotate P clockwise to increase the volume or counterclockwise to decrease the volume.

Channels and FrequenciesChannelFrequencyDescriptionChannelFrequencyDescription1462.5625 MHzGMRS/FRS MHzFRS2462.5875 MHzGMRS/FRS MHzFRS3462.6125 MHzGMRS/FRS MHzFRSStarted4462.6375 MHzGMRS/FRS MHzGMRS5462.6625 MHzGMRS/FRS MHzGMRSGetting6462.6875 MHzGMRS/FRS MHzGMRS7462.7125 MHzGMRS/FRS MHzGMRS8467.5625 MHzFRS MHzGMRS9467.5875 MHzFRS MHzGMRS MHzFRS MHzGMRS MHzFRS MHzGMRS. Talking and ListeningTo communicate, all radios in your group must be set to the same channel and Interference Eliminator Code.To talk, press and hold M. Hold the radio 2 to 3 inches away from your mouth when talking.When you finish talking, release M (press to talk, release to listen). Talk RangeYour radio is designed to maximize performance and improve transmission range. Do not use the radios closer than 5 feet apart.Checking the Channel Before TransmittingYour radio has multiple channels shared on a “take turns” basis.

For uninterrupted communication, do not talk on a channel if someone else is currently talking on it.To check for activity on a channel before you talk, press and hold Q or J. If you hear static, the channel is clear to use.

Special FeaturesInterference Eliminator CodeInterference Eliminator Codes help minimize interference by providing you with a choice of code combinations.To set the code for a channel:1. Press until the code starts to flash.2.

Press or to select the code.3. Press M to save the code setting.You can set a different code for each channel using this procedure.Note: You must set the Interference Eliminator Code to 0 on an FRS radio that uses Interference Eliminator Codes to communicate with other FRS radios that do not have Interference Eliminator Codes.Push to Talk Timeout TimerTo prevent accidental transmissions and save battery life, the radio emits a continuous warning tone and stops transmitting if you press Mfor 60 continuous seconds. Locking the KeypadTo avoid accidentally changing your radio settings, press and hold for 3 seconds or until f displays. You can turn the radio on and off, adjust the volume, receive, transmit, send a call tone, and monitor channels. All other functions are locked.To unlock the radio, press and hold for 3 seconds or until f is no longer displayed.Scanning Channels (Models T5620, T5700, T5710 Only)Use scanning to monitor channels and codes for transmissions or to find someone in your group who has accidentally changed channels.To start scanning, briefly press and release Q or J.

The scan indicator h displays.When the radio detects channel activity, it stops scanning and you can hear the transmission. To respond to the transmission, press M within 5 seconds. Scan AdvanceIf the radio stops scanning on a channel you do not want to listen to, briefly press and release or to resume scanning for the next active channel.Removing Channels from the Scan List (Nuisance Delete Feature)To remove a channel so the radio does not stop on it while scanning, press and hold or for at least 3 seconds, then release. This temporarily removes the channel from the scan list.To restore the channel, turn the radio off and then back on.Note: You cannot remove the channel your radio was set to when you started the scan (called your home channel).

Alerts Channel Busy IndicatorWhen a channel is busy, the LED flashes twice per second. Setting and Transmitting Call TonesYour radio can transmit different call tones to other radios in your group so you can alert them that you want to talk.To set a call tone:1. With the radio on, press 3 times. The current call tone setting flashes and E displays.2. Press or to change and hear the call tone.3. Press or M to set the new call tone.To transmit your call tone to other radios set to the same channel and Interference Eliminator Code as your radio, press ^.Notes.

The T5600, T5620, and T5700 models have 5 call tones. The T5710 and T5720 models have 10 call tones. Transmitting a Talk Confirmation ToneYou can set your radio to transmit a unique tone when you finish transmitting. It’s like saying Roger or Over to let others know you are finished talking. To turn talk confirmation on, press and hold while you turn the radio on. When you release M after transmitting, your call tone transmits! Displays.

To turn talk confirmation off, turn your radio off and then back on while pressing and holding.QT Noise Filtering (Models T5700, T5710, T5720 Only)The QT noise filtering feature helps ensure uninterrupted communication with other Motorola T5000 Series radios that have this feature. This feature filters out unwanted transmissions from other radios. It is useful in places where there is heavy radio traffic, such as at an amusement park or ski resort.Note: QT noise filtering is not available while the radio is scanning.To turn QT noise filtering on or off:1. Press until F displays.2. Press or until Y displays to turn noise filtering on, or until – displays to turn noise filtering off. To transmit to a radio that has QT noise filtering turned on:1.

Motorola Talkabout T5500 User Manual

Select the same channel and Interference Eliminator Code as the other radio.2. Press ^ to send a call tone. This allows your voice to pass through the QT noise filter on the receiving radio.3. Press M and speak normally.Note: If you skip step 2, the beginning of your message may not be heard on the receiving radio.For a 30-second period, starting after the last transmission, all transmissions received on the selected channel and code will pass through the QT noise filter. AccessoriesThere are many accessories (sold separately) available for your radio. For more information, refer to the brochure included with your radio, contact the place of purchase, call Motorola at 1-800-353-2729 in the USA or 1-800-739-7834 (TTY),or visit our website at www.motorola.com/talkabout.

Using Audio Accessories1. Turn the radio off. Plug the accessory connector into the jack. See page 12 and 13 for the location of the accessory jack on your radio.2. Turn the radio on. Lower the volume before placing the accessory on your head or in your ear.3.

Links FNAF 1-4 (ALL IN ONE zip file):http://www.mediafire.com/file/4198k6zkhw2spf4/FNAF+1-4.rar. Hope it helps. Download Links: FNAF 1. How to Download Five Night's at Freddy's 1, 2, and 3. Pronto Subire Todos Los FNaF 1,2,3,4,FNaF World,FNaF Sister location LInk: https://mega.nz/#!jc8kFQ5b! Fnaf 1 mediafire download.

Press Q or J while rotating P to adjust the volume to a comfortable level.4. To transmit, press M and speak into the accessory microphone, if any.5. To receive, release M.Voice Activation (VOX) Accessories (Models T5710, T5720 Only)Voice activation (VOX) allows you to talk handsfree when used with optional accessories connected to the radio. See the Motorola Talkabout accessory brochure for available VOX accessories.1. Turn the radio off. Insert the plug of the audio accessory firmly into the accessory jack (see page 13).3. Turn the radio on.

G displays.4. Lower the radio volume before placing the accessory on your head or in your ear.5. To transmit, speak into accessory microphone.

There is a short delay between the time you start talking and when the radio transmits.6. To receive, stop talking.To turn VOX off, press Mor remove the audio accessory.Setting the Sensitivity Level (Models T5710, T5720 Only)Adjusting your radio’s sensitivity level helps minimize the possibility of unintended noises triggering a transmission and helps the radio pick up soft voices.1. Press until g displays.2. Press or to select the sensitivity level:3 = High Sensitivity2 = Medium Sensitivity1 = Low Sensitivityfor quiet environmentsfor most environmentsfor noisy environments. Patent InformationThis product is manufactured under one or more of the following United States patents.582 56484 D408396 D399821 D3 580 5861850 D395882 D327 D38 59640 D413022 D493 D433001Export Law AssurancesThis product is controlled under the export regulations of the United States of America and Canada. The Governments of the United States of America and Canada may restrict the exportation or re-exportation of this product to certain destinations. For further information contact the U.S.

Motorola Talkabout 5500 Manual Download

Department of Commerce or the Canadian Department of Foreign Affairs and International Trade.